Vendita di attrezzature per l'apicoltura, arnie, smelatori e maturatori, miele e polline della Valtellina

-

-

-

-

-

-

-

-

Stainless steel SUBLIMATOR for OSSALIC ACID 12 VOLT DC/AC 150 WATT with off timer. Handle length 36 cm-thick 1.5 cm The start button starts the sublimator.A bright light signals 'on by turning off at the end of a preset time.This time can be launched from 1 to 4 minutes. Warranty 1 year

Stainless steel SUBLIMATOR for OSSALIC ACID 12 VOLT DC/AC 150 WATT with off timer. Handle length 36 cm-thick 1.5 cm The start button starts the sublimator.A bright light signals 'on by turning off at the end of a preset time.This time can be launched from 1 to 4 minutes. Warranty 1 year

How to perform the treatment 1) Hook up the terminals to the battery, respecting the polarity (red+, black -). After about 1 minute, you can proceed with the treatment. 2) Pour in 2.5 g. of oxalic acid with the dispenser provided for 10-frame Beehives, halving the dose for 6-frame Nucleus hives. 3) On average after 1 1/2 minutes you can switch to another Beehive; it is recommended not to turn off the device in treatment series. 4) Turn off BioletalVarroa® only at the end of the uninterrupted series of treatments to avoid overheating of the bowl and unnecessary energy consumption. 5) For practicality, less disturbance to the bees and better defense for the Beekeeper, we recommend to drill, on the back of the Beehive, a hole (45x12mm) skimming the bottom net, and perform the treatment from this , taking care to close with a cloth the entrance/exit bees from the step for about 5 minutes. This opening, after treatment, can be closed with a simple sheet of metal. 6) To perform the treatment from the entrance/exit bees from the step, it is recommended to operate with a wooden lath, or with a rag.

How to perform the treatment 1) Hook up the terminals to the battery, respecting the polarity (red+, black -). After about 1 minute, you can proceed with the treatment. 2) Pour in 2.5 g. of oxalic acid with the dispenser provided for 10-frame Beehives, halving the dose for 6-frame Nucleus hives. 3) On average after 1 1/2 minutes you can switch to another Beehive; it is recommended not to turn off the device in treatment series. 4) Turn off BioletalVarroa® only at the end of the uninterrupted series of treatments to avoid overheating of the bowl and unnecessary energy consumption. 5) For practicality, less disturbance to the bees and better defense for the Beekeeper, we recommend to drill, on the back of the Beehive, a hole (45x12mm) skimming the bottom net, and perform the treatment from this , taking care to close with a cloth the entrance/exit bees from the step for about 5 minutes. This opening, after treatment, can be closed with a simple sheet of metal. 6) To perform the treatment from the entrance/exit bees from the step, it is recommended to operate with a wooden lath, or with a rag.

-

-

-

-

Thanks to temperature control: - better evaporation of oxalic acid is achieved at the lowest possible temperature without running the risk that it, dissociating at higher temperatures, will lose effectiveness. - time is saved because there is no need to de-power and cool the sublimator between one treatment and the next treatment duration 1:30 minutes per Beehive - battery lasts longer - can run for thousands of treatment cycles. IN ADDITION: - the sublimator stops working before it has completely discharged (and therefore before it has ruined) the battery. - The electrical circuit is insulated from metal parts, so unlike other sublimators, there is no risk of short-circuit if several sublimators powered by the same battery come into contact with each other. Power supply characteristics: 12 volts - 120 watts (Battery not included). Treatment duration: about 1:30 minutes for 2 grams and 40 seconds for 1 gram oxalic acid (3 minutes if cooling the bowl in water between treatments). The oxalic acid is placed in the bowl which will be inserted into the flight opening. As the bowl is heated, the oxalic acid evaporates. A mist is thus formed in the Beehive that coats the bees and all surfaces with a thin layer of oxalic acid crystals. These small crystals are borne well by the bees but have a lethal action on varroa. The bowl is attached to a solid handle from which the 3-meter cable equipped with terminals for electrical connection departs. This sublimator complies with the European Directives, and therefore has a CE mark, and complies with the Rohs Directive on the restriction of the use of hazardous substances in electrical and electronic equipment.

Thanks to temperature control: - better evaporation of oxalic acid is achieved at the lowest possible temperature without running the risk that it, dissociating at higher temperatures, will lose effectiveness. - time is saved because there is no need to de-power and cool the sublimator between one treatment and the next treatment duration 1:30 minutes per Beehive - battery lasts longer - can run for thousands of treatment cycles. IN ADDITION: - the sublimator stops working before it has completely discharged (and therefore before it has ruined) the battery. - The electrical circuit is insulated from metal parts, so unlike other sublimators, there is no risk of short-circuit if several sublimators powered by the same battery come into contact with each other. Power supply characteristics: 12 volts - 120 watts (Battery not included). Treatment duration: about 1:30 minutes for 2 grams and 40 seconds for 1 gram oxalic acid (3 minutes if cooling the bowl in water between treatments). The oxalic acid is placed in the bowl which will be inserted into the flight opening. As the bowl is heated, the oxalic acid evaporates. A mist is thus formed in the Beehive that coats the bees and all surfaces with a thin layer of oxalic acid crystals. These small crystals are borne well by the bees but have a lethal action on varroa. The bowl is attached to a solid handle from which the 3-meter cable equipped with terminals for electrical connection departs. This sublimator complies with the European Directives, and therefore has a CE mark, and complies with the Rohs Directive on the restriction of the use of hazardous substances in electrical and electronic equipment.

Operation The timer allows setting the sublimation time through an internal 'trimmer', accessible through the hole provided on the top, and customizable according to the type of treatment. The default time is set in the 'family' mode at 1min 50sec, which corresponds to the treatment time for families on 10-frame Beehives; it is possible to set the timer to the nuclei mode by setting the trimmer to the 'core' position, which corresponds to 1min 20sec, with the help of the supplied accessory. By turning the same trimmer clockwise (to increase the time) and counterclockwise (to decrease the time), a duration from 0min to 5min can also be programmed. The end of the set treatment period is signaled by an audible warning emitted by a 'buzzer' inside the timer; it is possible to start a new treatment by pressing the 'start' button located on the top of the timer, which interrupts the buzzer and starts counting the set treatment time again. Installation The timer should be installed on the sublimator cable, and its location can be freely chosen by the beekeeper according to his or her preferences. However, it is important that the - polarity (blue wire) and + polarity (brown wire) are respected for the timer to operate properly. It is also possible to control 1 or 2 sublimators with a single timer by connecting the two wires of the same sublimators in and out. Two locations are recommended for the installation of the timer on the cable: - Close to the battery, if it is moved continuously near the beekeeper; - Close to the sublimators, leaving enough cable for the beekeeper to make the moves from one Beehive to another

Operation The timer allows setting the sublimation time through an internal 'trimmer', accessible through the hole provided on the top, and customizable according to the type of treatment. The default time is set in the 'family' mode at 1min 50sec, which corresponds to the treatment time for families on 10-frame Beehives; it is possible to set the timer to the nuclei mode by setting the trimmer to the 'core' position, which corresponds to 1min 20sec, with the help of the supplied accessory. By turning the same trimmer clockwise (to increase the time) and counterclockwise (to decrease the time), a duration from 0min to 5min can also be programmed. The end of the set treatment period is signaled by an audible warning emitted by a 'buzzer' inside the timer; it is possible to start a new treatment by pressing the 'start' button located on the top of the timer, which interrupts the buzzer and starts counting the set treatment time again. Installation The timer should be installed on the sublimator cable, and its location can be freely chosen by the beekeeper according to his or her preferences. However, it is important that the - polarity (blue wire) and + polarity (brown wire) are respected for the timer to operate properly. It is also possible to control 1 or 2 sublimators with a single timer by connecting the two wires of the same sublimators in and out. Two locations are recommended for the installation of the timer on the cable: - Close to the battery, if it is moved continuously near the beekeeper; - Close to the sublimators, leaving enough cable for the beekeeper to make the moves from one Beehive to another

-

-

-

-