Venta de equipos de apicultura, colmenas, extractores y maduradores de miel, miel y polen del Valle de Valtellina

Su forma especial permite colocarla en todas las colmenas Dadant Blatt, con o sin porche, y en las colmenas Langstroth de poliestireno La rejilla de polen con orificio trapezoidal para el paso de las abejas se puede girar para mantenerla abierta o cerrada. Las rejillas tienen 3 filas en la parte inferior, mientras que en los laterales el paso de las abejas aumenta. Una nervadura a ambos lados de la rejilla, en los agujeros y más allá, permite que las abejas se agarren y pasen más fácilmente.Si, al colocar la trampa en la colmena, la bandeja de polen se deja abierta, se facilita a las abejas el reconocimiento de un nuevo paso, y una vez bajada (cerrada) se reducen los posibles atascos.Una ranura muy ancha, antes de la bandeja de polen, permite a las abejas eliminar la suciedad de la Colmena.Dos orificios laterales sirven de paso para los zánganosUn techo muy ancho protege bien la trampa de las inclemencias del tiempo. La bandeja tiene una excelente ventilación y puede contener hasta 800 g de polen. La trampa de polen profesional también está equipada con una red para avispas asiáticas.La red para avispas, que se baja, permite a las abejas entrar y salir con mucha más tranquilidad, ya que la avispa asiática o la avispa velutina no pueden atacar a las abejas.La trampa está fabricada íntegramente con material plástico alimentario 100% reciclable, montado sin utilizar tornillos, clavos ni pegamentos tóxicos.

Su forma especial permite colocarla en todas las colmenas Dadant Blatt, con o sin porche, y en las colmenas Langstroth de poliestireno La rejilla de polen con orificio trapezoidal para el paso de las abejas se puede girar para mantenerla abierta o cerrada. Las rejillas tienen 3 filas en la parte inferior, mientras que en los laterales el paso de las abejas aumenta. Una nervadura a ambos lados de la rejilla, en los agujeros y más allá, permite que las abejas se agarren y pasen más fácilmente.Si, al colocar la trampa en la colmena, la bandeja de polen se deja abierta, se facilita a las abejas el reconocimiento de un nuevo paso, y una vez bajada (cerrada) se reducen los posibles atascos.Una ranura muy ancha, antes de la bandeja de polen, permite a las abejas eliminar la suciedad de la Colmena.Dos orificios laterales sirven de paso para los zánganosUn techo muy ancho protege bien la trampa de las inclemencias del tiempo. La bandeja tiene una excelente ventilación y puede contener hasta 800 g de polen. La trampa de polen profesional también está equipada con una red para avispas asiáticas.La red para avispas, que se baja, permite a las abejas entrar y salir con mucha más tranquilidad, ya que la avispa asiática o la avispa velutina no pueden atacar a las abejas.La trampa está fabricada íntegramente con material plástico alimentario 100% reciclable, montado sin utilizar tornillos, clavos ni pegamentos tóxicos.

Con bandeja extraíble , posibilidad de mantener abierto el paso de las abejas incluso con la trampa montada , orificio para el paso de los zánganos

Con bandeja extraíble , posibilidad de mantener abierto el paso de las abejas incluso con la trampa montada , orificio para el paso de los zánganos

Su forma especial permite colocarla en todas las colmenas, Dadant Blatt, con o sin porche, y colmenas Langstroth de poliestireno La rejilla de polen con agujeros redondos para el paso de las abejas se puede girar para mantenerla abierta o cerrada. Las rejillas tienen 3 filas en la parte inferior, mientras que en los laterales el paso de las abejas aumenta. Una nervadura a ambos lados de la rejilla, en los agujeros y más allá, permite que las abejas se agarren y pasen más fácilmente.Si, al colocar la trampa en la colmena, la bandeja de polen se deja abierta, se facilita a las abejas el reconocimiento de un nuevo paso, y una vez bajada (cerrada) se reducen los posibles atascos.Una ranura muy ancha, antes de la bandeja de polen, permite a las abejas eliminar la suciedad de la Colmena.Dos agujeros laterales sirven de paso para los zánganosUn techo muy ancho protege bien la trampa de las inclemencias del tiempo. La bandeja tiene una excelente ventilación y puede contener hasta 800 g de polen. La trampa de polen profesional también viene con una red para avispas asiáticas.La red para avispas, que se baja, permite a las abejas entrar y salir con mucha más tranquilidad, ya que la avispa asiática o la avispa velutina no pueden atacar a las abejas.La trampa está fabricada íntegramente con material plástico alimentario 100% reciclable, montado sin utilizar tornillos, clavos ni pegamentos tóxicos.

Su forma especial permite colocarla en todas las colmenas, Dadant Blatt, con o sin porche, y colmenas Langstroth de poliestireno La rejilla de polen con agujeros redondos para el paso de las abejas se puede girar para mantenerla abierta o cerrada. Las rejillas tienen 3 filas en la parte inferior, mientras que en los laterales el paso de las abejas aumenta. Una nervadura a ambos lados de la rejilla, en los agujeros y más allá, permite que las abejas se agarren y pasen más fácilmente.Si, al colocar la trampa en la colmena, la bandeja de polen se deja abierta, se facilita a las abejas el reconocimiento de un nuevo paso, y una vez bajada (cerrada) se reducen los posibles atascos.Una ranura muy ancha, antes de la bandeja de polen, permite a las abejas eliminar la suciedad de la Colmena.Dos agujeros laterales sirven de paso para los zánganosUn techo muy ancho protege bien la trampa de las inclemencias del tiempo. La bandeja tiene una excelente ventilación y puede contener hasta 800 g de polen. La trampa de polen profesional también viene con una red para avispas asiáticas.La red para avispas, que se baja, permite a las abejas entrar y salir con mucha más tranquilidad, ya que la avispa asiática o la avispa velutina no pueden atacar a las abejas.La trampa está fabricada íntegramente con material plástico alimentario 100% reciclable, montado sin utilizar tornillos, clavos ni pegamentos tóxicos.

-

-

-

-

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

-

-

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

-

-

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

With removable tray , possibility to keep bee passage open even with trap mounted , hole for drones passage

-

-

-

-

-

-

-

-

-

-

-

-

Our professional pollen catcher trap has the advantage that it can be applied to virtually all existing Beehives, even those that have an entrance from above, and very easily. By attaching two different sheet metal canopies that protect it from the rain on the top, two different planes of support on the wall are created, and it can be applied to STANDARD Beehives with the porch (item LA 2405) and to KUBIK Beehives (item LA 2407). The trap rests on the step and is quickly attached to the front wall of the Beehive with two eye screws in prepared slots. The two clear plastic tubes inserted on either side of the trap are exactly level with the base net and facilitate cleaning by the bees. The "pollen peeler" grid is made of plastic, has only three horizontal rows of round holes and special longitudinal brackets at the base of the holes on which the bees rest before passing through the holes and losing the pollen pellets. The base net, on which the pollen falls before ending up in the box measures 90x360 mm and is made of AISI 304 stainless steel. On the top of the vertical wall supporting the grid are 6 transparent plastic cones with the tips pointing outward, which function as a one-way exit for drones and bees, but are not recognized by the bees as an entrance. The pollen collector drawer has a bottom made of AISI 304 stainless steel mesh, has a large size (330x90x110 mm) with a capacity of about 3300 cm³, and is pulled out by sliding it on two metal guides. (The average yield on a good day can exceed 500 grams.) The galvanized sheet metal canopy protrudes forward and protects the pollen contained in the drawer from rain.

Our professional pollen catcher trap has the advantage that it can be applied to virtually all existing Beehives, even those that have an entrance from above, and very easily. By attaching two different sheet metal canopies that protect it from the rain on the top, two different planes of support on the wall are created, and it can be applied to STANDARD Beehives with the porch (item LA 2405) and to KUBIK Beehives (item LA 2407). The trap rests on the step and is quickly attached to the front wall of the Beehive with two eye screws in prepared slots. The two clear plastic tubes inserted on either side of the trap are exactly level with the base net and facilitate cleaning by the bees. The "pollen peeler" grid is made of plastic, has only three horizontal rows of round holes and special longitudinal brackets at the base of the holes on which the bees rest before passing through the holes and losing the pollen pellets. The base net, on which the pollen falls before ending up in the box measures 90x360 mm and is made of AISI 304 stainless steel. On the top of the vertical wall supporting the grid are 6 transparent plastic cones with the tips pointing outward, which function as a one-way exit for drones and bees, but are not recognized by the bees as an entrance. The pollen collector drawer has a bottom made of AISI 304 stainless steel mesh, has a large size (330x90x110 mm) with a capacity of about 3300 cm³, and is pulled out by sliding it on two metal guides. (The average yield on a good day can exceed 500 grams.) The galvanized sheet metal canopy protrudes forward and protects the pollen contained in the drawer from rain.

-

-

Our professional pollen catcher trap has the advantage that it can be applied to virtually all existing Beehives, even those that have an entrance from above, and very easily. By attaching two different sheet metal canopies that protect it from the rain on the top, two different planes of support on the wall are created, and it can be applied to STANDARD Beehives with the porch (item LA 2405) and to KUBIK Beehives (code LA 2407). The trap rests on the step and is quickly attached to the front wall of the Beehive with two eye screws in prepared slots. The two clear plastic tubes inserted on either side of the trap are exactly level with the base net and facilitate cleaning by the bees. The "pollen peeler" grid is made of plastic, has only three horizontal rows of round holes and special longitudinal brackets at the base of the holes on which the bees rest before passing through the holes and losing the pollen pellets. The base net, on which the pollen falls before ending up in the tray measures 90x360 mm and is made of AISI 304 stainless steel. On the top of the vertical wall supporting the grid are 6 transparent plastic cones with the tips pointing outward, which function as a one-way exit for drones and bees, but are not recognized by the bees as an entrance. The pollen collector drawer has a bottom made of AISI 304 stainless steel mesh, has a large size (330x90x110 mm) with a capacity of about 3300 cm³, and is pulled out by sliding it on two metal guides. (The average yield on a good day can exceed 500 grams). The galvanized sheet metal canopy protrudes forward and protects the pollen contained in the drawer from rain.

Our professional pollen catcher trap has the advantage that it can be applied to virtually all existing Beehives, even those that have an entrance from above, and very easily. By attaching two different sheet metal canopies that protect it from the rain on the top, two different planes of support on the wall are created, and it can be applied to STANDARD Beehives with the porch (item LA 2405) and to KUBIK Beehives (code LA 2407). The trap rests on the step and is quickly attached to the front wall of the Beehive with two eye screws in prepared slots. The two clear plastic tubes inserted on either side of the trap are exactly level with the base net and facilitate cleaning by the bees. The "pollen peeler" grid is made of plastic, has only three horizontal rows of round holes and special longitudinal brackets at the base of the holes on which the bees rest before passing through the holes and losing the pollen pellets. The base net, on which the pollen falls before ending up in the tray measures 90x360 mm and is made of AISI 304 stainless steel. On the top of the vertical wall supporting the grid are 6 transparent plastic cones with the tips pointing outward, which function as a one-way exit for drones and bees, but are not recognized by the bees as an entrance. The pollen collector drawer has a bottom made of AISI 304 stainless steel mesh, has a large size (330x90x110 mm) with a capacity of about 3300 cm³, and is pulled out by sliding it on two metal guides. (The average yield on a good day can exceed 500 grams). The galvanized sheet metal canopy protrudes forward and protects the pollen contained in the drawer from rain.

METHOD OF USEThese pollen-collecting bottoms, having a tilting entrance, allow pollen collection by simply raising the movable part.1. You raise the movable part of the pollen-collecting bottom until the hive door is fully closed2. You lock the movable part, thus opening the entrance to the grid3. Bees are forced through the pollen-collecting grid, allowing collection through drawers constructed of wood and stainless mesh.

METHOD OF USEThese pollen-collecting bottoms, having a tilting entrance, allow pollen collection by simply raising the movable part.1. You raise the movable part of the pollen-collecting bottom until the hive door is fully closed2. You lock the movable part, thus opening the entrance to the grid3. Bees are forced through the pollen-collecting grid, allowing collection through drawers constructed of wood and stainless mesh.

.

.

-

-

-

-

-

-

-

-

-

-

-

-