WINTER DRIPED: Dosage: drip with syringe 8-10 ml of warm solution per frame. Use 50-80 ml per colony Preparation: for a 275 g bottle add 275 g sugar and mix (1:1 solution) DRILLED OR SPRAYED SUMMER: Dosage: for swarms use 20-25 ml per kg of bee mass, for nuclei and colonies without brood spray 2-4 ml per side of frame. Preparation: for 275 g bottle add 250 ml of drinking water.Posology and route of administration The product should be used as follows : A) Application by drip: Preparation of ready-to-use 3.5% (m/V) oxalic acid dihydrate solution for drip: Pre-heat the container of oxalic acid dihydrate solution in a water bath (30-35 °C). Remove from the water bath and open the sealed container. Add the required amount of sugar (sucrose) of the type used for bee feeding: - 275 g sugar when using the 275 g bottle - 1 kg sugar when using the 1000 g bottle Close the container and shake vigorously until the sugar has completely dissolved. The solution is ready for use and should be applied lukewarm. Administration Fill a syringe (60 ml) or similar device through the wide opening of the container with the required amount of ready-to-use solution to treat one colony. The dose per frame is : 0.25 ml/dm2 for Western/Central Europe and 0.4 ml/dm2 for Southern Europe. For two-chamber Beehives, drip the lower nest first and then the upper nest. Mite drop will continue for 3 weeks The ready-to-use drip solution is sufficient to treat 6 to 15 colonies when using the 275 g bottle or 20 to 50 colonies when using the 1000 g bottle. The ready-to-use drip solution should be used immediately and cannot be stored after preparation. B) Application by spraying: Preparation of ready-to-use 3% (m/V) solution of oxalic acid dihydrate for spraying: Add drinking water to the solution: - 250 g (250 ml) of drinking water when using the 275 g bottle; - 900 g (900 ml) of drinking water when using the 1,000 g bottle, Close the container and shake. The solution is now ready for use. Administration Fill a hand sprayer or similar device with the required amount of ready-to-use solution to treat one colony. Spray 2-4 ml of solution on each side of the frame covered by the bees. If only half of the frame is covered with bees, the dosage should be reduced by 50%. The maximum dose is 80 ml. The total volume required varies according to the type of Beehive: - Colonies without brood, artificial colonies without brood or swarms newly placed in the Beehive should be treated with a dose of 0.3 ml/dm2 of frame completely covered with bees and for most hives. - Swarms, artificial swarms in glomeres should be sprayed with 20-25 ml of ready-to-use spray solution per kg of bees. For accurate spray dosing with your hand sprayer, spray 10 times into a measuring cup and calculate the volume for each pumping action. Calculate how many pumping actions are needed to treat one side of the frame. The frames should be sprayed at a 45° angle so as to minimize direct spraying into the cells. Mite fall will continue for 3 weeks. Treat swarm, artificial swarm or artificial broodless colony in spring/summer as a single treatment when most bees are inside the Beehive (in the evening). The ready-to-use spraying solution is sufficient to treat 5 to 10 colonies using the 275g bottle or 25 to 40 colonies using the large 1,000g bottle.

Colmena D.B. pintada de 10 cuadros, con marcos de nido y cría. Completa con: Nido; panal; tapa de madera con disco de chapa montado de 4 posiciones; tapa de chapa galvanizada de 10 cm de altura forrada de madera y faestile en la parte inferior; tejadillo de chapa galvanizada; marcos en el nido y en el panal con alambre sin cera; máscara de transporte de plástico; molinetes galvanizados puerta metálica; 3 ángulos de conexión; distanciadores montados en el nido y en el panal; fondo de red antipolillas fijo con fondo de chapa galvanizada desmontable por la parte trasera; madera de abeto sazonada de 25 mm de grosor; paredes montadas con tornillos; asas para transporte; Soporte para palanca

- Accesorios11) Alza de 6 marcos D.B. (Cod. QI M60)12) Separador frontal (Cod. QI D32)13) Refuerzo lateral (Cod. QI R128)14) Cubierta de poliestireno con malla (Cod. QI C16)15) Cubierta y malla de madera (Cod. PI 38/A)16) Cubierta de chapa perforada (Cod. FO 1045)17) Cubierta de plástico perforada (Cod. ES RT)18) Cubierta de chapa (Cod. FO 1042)- Puertas pequeñas 21) Puerta pequeña galvanizada en posición central (Cod. QI P25)22) Puerta de protección galvanizada con corredera (Cod. QI P35)23) Corredera de recambio con trampilla de protección (Cód. QI P36)- Alimentadores31) Alimentador de tapa de cable de 1 orificio (Cód. QI N06)32) Alimentador de tapa de cable de 1 orificio nuevo (Cód. QI N07)33) Alimentador de tapa de cable de doble compartimento (Cód. QI N12)34) Campana de repuesto (Código QI C97)35) Vulcanello de repuesto (Código QI C107)- Piezas de repuesto 41) Puerta de poliestireno (Código QI P21)42) Tapa de poliestireno (Código QI C16B)

Painted 10-frame D.B. Beehives, with honeycomb and 10 frames in the nest and 9 in the Honey super. Complete with: Nest; Honey super; wooden honeycomb cover with mounted 4-position sheet metal disc; 10cm-high galvanized sheet metal lid lined with wood and faestile on bottom; galvanized sheet metal canopy; frames in nest and honeycomb with wax-free wire; plastic transport mask; galvanized pinwheels; metal porch; 3 connection angles; spacers mounted in the nest and honeycomb; mobile antivarroa net bottom with galvanized sheet metal tray removable from the back; 25mm thick seasoned spruce wood; walls assembled with screws; handles for transport; Frame rest